Fanatec CSL DD 0,5 - FFB Settings for rFactor 2 [OW]

[pocisk]

Hi, after a few weeks of testing, finally happy to share the rF2 setup for OW cars.

Settings for the CSL DD Boost Kit 180 Bundle:

• Set 1 - for 'peak' mode (8 Nm):

• Set 5 - for 'linear' mode (6 Nm):

These settings should be fine for most open-wheel cars in rF2.

For your preferences:

In Fanatec Controll Panel:
FFB [Overall FFB Strength] & FOR [Force Effect Strength]

In rFactor 2:
FFB Smoothing & FFB Multi.


Also edited few options in my Controller.JSON [rFactor2 / UserData / Controller]:

"Steering resistance coefficient":0,
"Steering resistance saturation":0,
[via @Marko: https://forum.studio-397.com/index.php?threads/csl-dd-ffb-issue.70404/#post-1081462]


"Steering torque capability":8, [or 6 - for 6 Nm base]
"Steering resistance type":1,

Cheers

 

[stewie007]

so you pay huge amount of money and then fanatec doesnt give the buyer the ffb information? great...
that is bad support.

 

[pocisk]

so you pay huge amount of money and then fanatec doesnt give the buyer the ffb information? great...
that is bad support.

No, they are here:

rFactor 2 (PC) - Fanatec Recommended Settings

General Notes: - The settings below are considered to be reasonable baseline values for rFactor 2 (PC).

forum.fanatec.com

I just made my own, dedicated for open wheelers (which I like most)

 

[stewie007]

do u feel a relevant difference between ur 20nm wheel base and a 8nm like cdl dd?

 

[pocisk]

do u feel a relevant difference between ur 20nm wheel base and a 8nm like cdl dd?

I don't have DD1 / DD2 base, but from what I've heard no one is using 100% ffb force.
8 Nm is good enough for me

 

[Butthurt_Saddle_sore]

I am going to have to try this. I just ran RF2, and whatever settings I had on the wheel made the game feel cursed. The wheel was maximum strength with every FFB effect the game threw at it. I was about to load a suggestion setup from Fanalabs, but then I didn't want to go down that rabbit hole right now. I'll give your 8nm settings a go. It's going to be way better than what I just experienced.

 

[Durge Driven]

I tried the Fanalab profile with these settings, and was good
Major difference I lowered FEI way down with Historic open wheel
Specially considering I am using podium 911 which is too slow for old cars
My CSP 280m round V2 has arrived, going to try out tonight, same 3 x 1 hour races for direct compare
Nice finally having 2 complete wheels to use
Best races I had since I got CSL DD, I can't believe anyone had the same experience would not fall in love

 

[pocisk]

I tried the Fanalab profile with these settings, and was good
Major difference I lowered FEI way down with Historic open wheel
Specially considering I am using podium 911 which is too slow for old cars
My CSP 280m round V2 has arrived, going to try out tonight, same 3 x 1 hour races for direct compare
Nice finally having 2 complete wheels to use
Best races I had since I got CSL DD, I can't believe anyone had the same experience would not fall in love

Great to hear that, have fun ;-)

 

[Rebel_488]

setting ffb in game to device driver made a diff for me

 

[mesfigas]

@pocisk why have FFb type to Software instead of device ?
i use a csl elite ps4 version

 

[mmmarac]

With those settings and DPR at 100, if you restart the race a few times, FFB on CSL DD starts buzzing and making some grinding noise when you steer. I tought my base was mulfunctioning but I guess I’m not the only one.
https://forum.studio-397.com/index.php?threads/csl-dd-ffb-issue.70404/

 

[Nortski]

With those settings and DPR at 100, if you restart the race a few times, FFB on CSL DD starts buzzing and making some grinding noise when you steer. I tought my base was mulfunctioning but I guess I’m not the only one.
https://forum.studio-397.com/index.php?threads/csl-dd-ffb-issue.70404/

Yup, I had this very problem too. Solved it by reducing the dampening setting to 0%.

 

[Henry2211]

What is the difference between steering type damper ot friction?