Hi i cant play this game if i try to map gas pedal on sim pedals then it unasigns right steering for my csw v2?
Anyone know how i can fix this.
Anyone know how i can fix this.
F1 2015 Fanantec CSW
- Thread starter William Moody
- Start date
F1 2015 The Game (Codemasters)
Ok i fixed this problem with changing the axis for pedals with the connections.
Now there seems to be a huge deadzone on the pedals both the gas and brake pedals lmao.
Now there seems to be a huge deadzone on the pedals both the gas and brake pedals lmao.
Hi, does anyone know the best settings for the CSW or where I can find them? ALso, the ps4 only has 2 usb connections and the CSW wheel and pedals use both. Is there any way I can use a headset as well? It seems not...
thanks!
thanks!
I have the same issue with the Axis, can you expand on what yo did to solve it ?
edit: i think i understand so im going to switch the throttle to the clutch axis using the little HE connector box.
Last edited:
Yes thats what i done Carl but once you have done that you will notice a huge deadzone on the pedals.
I havent needed to switch the connectors, and still have the massive deadzone on my fanatec CSR elite pedals... it makes the game unplayable, which is a shame because this is the only issue i have had and from what i have played the physics and handling are the best codemasters have done for F1.
I had deadzones in the pedals but my CSPv2 were plugged into the comp directly. I plugged them into the wheel base and now the pedals work fine.
There's also a setting that can be adjusted and some claim success with it: read here.
There's also a setting that can be adjusted and some claim success with it: read here.
Has anyone managed to figure out a solution to the deadzone issue with the HE Pedals yet ?
Im using the csw and f1 rim on ps4 but since I connected the pedals to the wheel unit (ie the ps4 config), if I press throttle I get wheel vibration - even when the ps4 is not even on!
Any ideas?
Any ideas?
Do you have ABS configured with the the wheel?
I had a similar issue with ABS set to off on the wheel, but once I changed the value to a number, both the wheel base and the brake stopped vibrating aggressively under full throttle. I am racing, however, the PC edition of the game.
Well done fanatec, and thanks billymitchell - ive just seen your reply above. Anyone else who gets stuck, see below.
Hello Paul,
thank you for your enquiry.
Please check this FAQ https://www.fanatec.com/eu-en/support/faq/details&id=37, especially SHO and ABS. There you will find a description what to do.
Best regards / Freundliche Grüße
Hello Paul,
thank you for your enquiry.
Please check this FAQ https://www.fanatec.com/eu-en/support/faq/details&id=37, especially SHO and ABS. There you will find a description what to do.
Best regards / Freundliche Grüße
Reedy - a couple of suggestions:
- make sure that the pedal set is plugged into the wheel, then the wheel into the ps4 via usb AND MAKE SURE you haven't left the cable for the pc setup still plugged in..look for the warning sign on the pedals near the connection for advice (or if pc, both need to be usb into the pc)
- try pressing the tiny button just to the left of the lcd display on the wheel, to get access to the in-wheel config. It will say 'S_1' or similar. You can even do this with console or pc turned off, it makes no difference.
Hope this helps!
- make sure that the pedal set is plugged into the wheel, then the wheel into the ps4 via usb AND MAKE SURE you haven't left the cable for the pc setup still plugged in..look for the warning sign on the pedals near the connection for advice (or if pc, both need to be usb into the pc)
- try pressing the tiny button just to the left of the lcd display on the wheel, to get access to the in-wheel config. It will say 'S_1' or similar. You can even do this with console or pc turned off, it makes no difference.
Hope this helps!
