FS complete simvibe/simhub hardware setup - SOLD!
I have recently completed my SFX-100 motion project, prior to that I was running two amps and 6 transducers/shakers in Chassis and Extension mode, I no longer need Chassis mode so I have an amp and transducers surplus to requirements, along with four Simlab mounts and sound card to amp wiring.
The amp is a 4 channel Stageline-1504 bought Dec 2016
https://www.amazon.co.uk/gp/product/B000WWLKFA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Used by the Shaker centre in their Simvibe gaming package.
4x160wrms 4ohm 4x100wrms 8ohm
Balanced inputs
Protected against short circuit and overheating
Durable heavyweight design ideal for installations
The transducers are Reckhorn BS-200i Bass Shaker 100w
https://shakercentre.co.uk/gaming-simulation/reckhorn-bs-200-bass-shaker.html
Technical information
Power Handling (RMS): 100 Watts
Impulse Power (2 seconds): 200 Watts
Impedance: 4 Ohm
Diameter: 158mm
Height: 45mm
Weight: 1.2 kg
Mounting Hole Diameter (3): 5mm
The amp will need to be turned down a fraction to cater for 100watts.
Finally four Simlab mounts designed for attaching to 8020 Aluminium profile.
https://sim-lab.eu/product/buttkicker-shaker-mounting-plate/
All you will need to do is pay shipping or collect from the Berkshire area RG7, dig out some speaker wire for amp to transducer and buy or download software to run it all, Simvibe is commercial, I believe Simhub is open source.
I would like £300 plus shipping as a bundle, buying all this new will top £550.
UK only, this amp weighs a lot and shipping will cost money, I will only ship insured at new value unless buyer arranges courier, then it is their risk, if you want to use paypal I will not pay fees, bank transfer acceptable.
I have recently completed my SFX-100 motion project, prior to that I was running two amps and 6 transducers/shakers in Chassis and Extension mode, I no longer need Chassis mode so I have an amp and transducers surplus to requirements, along with four Simlab mounts and sound card to amp wiring.
The amp is a 4 channel Stageline-1504 bought Dec 2016
https://www.amazon.co.uk/gp/product/B000WWLKFA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Used by the Shaker centre in their Simvibe gaming package.
4x160wrms 4ohm 4x100wrms 8ohm
Balanced inputs
Protected against short circuit and overheating
Durable heavyweight design ideal for installations
The transducers are Reckhorn BS-200i Bass Shaker 100w
https://shakercentre.co.uk/gaming-simulation/reckhorn-bs-200-bass-shaker.html
Technical information
Power Handling (RMS): 100 Watts
Impulse Power (2 seconds): 200 Watts
Impedance: 4 Ohm
Diameter: 158mm
Height: 45mm
Weight: 1.2 kg
Mounting Hole Diameter (3): 5mm
The amp will need to be turned down a fraction to cater for 100watts.
Finally four Simlab mounts designed for attaching to 8020 Aluminium profile.
https://sim-lab.eu/product/buttkicker-shaker-mounting-plate/
All you will need to do is pay shipping or collect from the Berkshire area RG7, dig out some speaker wire for amp to transducer and buy or download software to run it all, Simvibe is commercial, I believe Simhub is open source.
I would like £300 plus shipping as a bundle, buying all this new will top £550.
UK only, this amp weighs a lot and shipping will cost money, I will only ship insured at new value unless buyer arranges courier, then it is their risk, if you want to use paypal I will not pay fees, bank transfer acceptable.
Last edited:
