Paul Jeffrey

Premium
We talk to Niels Heusinkveld and try out the soon to be released Heusinkveld Sim Pedals Sprint.

Catching up with Niels Heusinkveld at the recent very busy Sim Racing Expo over in Germany, we took the opportunity to quiz the man behind Heusinkveld Engineering about his newly announced Sim Pedals Sprint set of high end sim racing pedals. With Niels in a buoyant mood following what appeared to be a largely very positive reception to the new hardware, we took the opportunity to question him about the features and improvements of the new gear, learning plenty about how some dramatic software features and production improvements have moved the product range on from the already very impressive offerings of HE Engineering.

Not content with merely taking Niels at his word, we also couldn't quite resist the chance to get strapped into the cockpit and have a go ourselves, recording a short but sweet talk and drive segment as we give our first impressions based on the limited time we had with these brand new set of pedals.

Frankly, I was very impressed, although it is exceptionally hard to gather any serious kind of feel with something like a high end set of pedals with such a short period of time behind the wheel... not helped any by a crowd of people watching on, and a camera and microphone in my face!

However, with that said I'm going to be lucky enough to take receipt of a review set of these pedals in the very near future, so please consider this more of a taster video, with a much more in depth and detailed look at the HE Sim Pedals Sprint set to appear on our various social media channels in the near future. So stay tuned, get subscribed and watch out for some new footage in the (hopefully) coming weeks...

Heusinkveld Sim Pedals Sprint Talk n Drive.jpg


Like what we do at RaceDepartment? Follow us on Social Media!

 
 
Last edited:
I feel your pain :(

I ended up removing the heel plate to get access to the pesky bolts and then re-mounted the heel plate once the rails were bolted in place. I nearly took the pedals off too but somehow managed to get the bolts started in the t-slot nuts. Once you get the thread going it gets easier (a bit.. ) .

Good luck anyway ! It’s worth the effort ;)
 
Upvote 0
They're meant to be like that. View attachment 308904
Besides, it doesn't matter all that much where you have the larger diameter spacers, just as long as they're on both sides of the rubber, and in between rubbers if you use multiple.

Thanks for clarifying that.

I think the slight confusion comes from the picture in the manual called "Available brake stiffness settings"

In that picture the illustration shows a slightly different order of arrangement for the default setting. No big deal though :)
 
Upvote 0
Thanks for clarifying that.

I think the slight confusion comes from the picture in the manual called "Available brake stiffness settings"

In that picture the illustration shows a slightly different order of arrangement for the default setting. No big deal though :)

Mine was set just like the default configuration with the XL rubber.
 
Upvote 0
Mine was set just like the default configuration with the XL rubber.
I'm guessing they decided to make a change at some point after the v1 went to print.

I'll most likely spend far too many hours faffing around to test out the range of feeling that can be achieved. I'm also thinking of using the "I had the brake rubbers in the wrong order" excuse for my terrible lap times :whistling:
 
Upvote 0
I'm guessing they decided to make a change at some point after the v1 went to print.

I'll most likely spend far too many hours faffing around to test out the range of feeling that can be achieved. I'm also thinking of using the "I had the brake rubbers in the wrong order" excuse for my terrible lap times :whistling:

Actually I think mine might have been the same, I’ve since changed it to the next harder configuration so forgot but I did take one photo beforehand.

B3236435-E31-A-4-DDA-B90-B-F6-CE8-C249768.jpg
 
Upvote 0
I managed to set up my Sprints and base plate last night.

Other than the 2 rear mounting bolts of the base plate to rig being a fiddley-faff everything went smoothly.

The only thing I cant do is loosen the bolt holding the brake plate on, so I can turn it round. Its super tight. On the rear is a locking nut, but the problem is its so tight the allen bolt on the face side will round off if I give it anymore torque. Any ideas?

My hamstrings are aching this morning after a few hours use last night :roflmao: Abit of fine tuning is required I think :thumbsup:
 
Upvote 0
I managed to set up my Sprints and base plate last night.

Other than the 2 rear mounting bolts of the base plate to rig being a fiddley-faff everything went smoothly.

The only thing I cant do is loosen the bolt holding the brake plate on, so I can turn it round. Its super tight. On the rear is a locking nut, but the problem is its so tight the allen bolt on the face side will round off if I give it anymore torque. Any ideas?

My hamstrings are aching this morning after a few hours use last night :roflmao: Abit of fine tuning is required I think :thumbsup:

Same issue I had with the Throttle plate which did round the bolt as it was so tight, I had a little Draper ratchet so used that instead of the little spanner that you can’t get a good grip on the nut on the other side with and I loosened from the nut instead of the bolt and that seemed a bit easier on it, but as the bolt wouldn’t take an Allen key anymore I had to use a star shaped Torx head screw driver to hold it as I turned the ratchet.
 
Last edited:
Upvote 0
Cheers... As suspected then. I really didnt want to be bodging tools in my new pedals.... Problem is without returning the whole lot what can you do.

That’s the only thing you can do if you want to lower that plate I guess, if you have other tools to do the job with better grip on the nut and bolt then give it a go, not sure I’d want to use a drill on it. Just be slow and careful with it, if you don’t have the tools I’m not sure, don’t know if they will replace the whole pedal to sort it out for you, maybe. Anyone else got any ideas in here?
 
Upvote 0
My brake pedal started spiking today and reads 65kg even though I'm hardly pressing the pedal. Only had these for 4 months. I have never modified them and just used them as is straight out the box. :(

 
Upvote 0
My brake pedal started spiking today and reads 65kg even though I'm hardly pressing the pedal. Only had these for 4 months. I have never modified them and just used them as is straight out the box. :(

This is the issue that was mentioned before. We've seen a small percentage of brakes fail and we've updated the loadcell mount so it doesn't happen anymore. Send us an email at support@heusinkveld.com and I'll ship a new brake to you.
 
Upvote 0
I have a problem: after installing my pedals, the cable that goes from the throttle to the brake is 1 cm short. They are in a fix position so moving them close means making new drills and it would be a hassle. Is there a way to fix this problem, any kind of standard extender? I could cut the cable and join all the tiny cables one by one, but would that void the warranty?
 
Upvote 0

Latest News

Shifting method

  • I use whatever the car has in real life*

  • I always use paddleshift

  • I always use sequential

  • I always use H-shifter

  • Something else, please explain


Results are only viewable after voting.
Back
Top